Dakota Digital CLK 1002B User Manual

CLK-1002B rev. A  
DIGITAL CLOCK TO MATCH VFD-1002B  
Introduction:  
The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our  
standard gauges, along with several unique features and easy mounting. These features include:  
Quartz accuracy.  
Night dimming feature.  
Very low standby power to prevent battery drain.  
High Visibility VFD display for sunlight readability.  
The Odyssey series clock displays the current time in 12 hour format. The high brightness display  
matches our other Odyssey and STR series gauges and has the same night brightness dimming capability.  
Operation:  
The gauge needs the red, orange, and black wires connected to operate. The red wire should have  
switched 12 volt power from an ACC. point on the fuse panel. The orange wire should have constant 12 volt  
power. The black wire should be connected to a good ground point. When the blue wire has 12 volts, it will dim  
the display for night viewing.  
Setting the time:  
Using a small, thin object such as a toothpick or pin, press “set” buttons through front lens access holes.  
The access holes are on the right side of the lens. Top “set” button advances hours, bottom “set” button  
advances minutes. Each time that you make a change to either the hours or minutes, the seconds are reset to  
zero.  
Adjusting the accuracy:  
The clock is accurate to +/-2 minutes a month as it is sent. It can be tuned for better accuracy if  
desired. Press and hold both of the set buttons for several seconds. The clock will display “C 0”. The “C”  
indicates that it is in the calibration mode and the second number is the current calibration value. The  
calibration value indicates the number of seconds to add or subtract each day. The clock can be adjusted from  
+7 sec/day to -7 sec/day.  
Press the minute set button to change the cal value. Press the hour set button to return to normal clock  
operation.  
Troubleshooting guide.  
Problem  
Possible cause  
Solution  
Clock will not light up  
Red wire does not have  
power.  
Connect to a location that has power  
when the key is on.  
Orange wire does not have  
power.  
Connect to a location that has power  
all of the time.  
Black wire is not getting  
a good ground.  
Connect ground to a different location.  
Power is reversed.  
Connect black to negative ground, red and  
orange to +12V power.  
Clock is damaged.  
The red and orange wires  
are reversed.  
Return clock for repair. (see instructions)  
Connect the red to switched power, the  
orange to constant power.  
Clock will not turn off when  
the key is off.  
Clock lights up, but does  
not read correctly.  
Loose connection on orange  
power wire.  
Reconnect orange wire.  
Poor ground connection.  
Time is not set.  
Move ground to different location  
Set time. (see instructions)  
Clock is damaged.  
Orange wire does not have  
constant power.  
Return clock for repair. (see instructions)  
Connect to a location that has power when  
the key is on or off.  
Clock will not keep time.  
Loose connection on orange  
power wire.  
Reconnect orange wire.  
Poor ground connection.  
Blue wire is not connected  
correctly.  
Move ground to different location  
Check wiring connections.  
Clock will not dim.  
Clock remains dim at all  
times.  
Blue wire is getting power  
all of the time.  
Battery is very low.  
Clock is damaged.  
Connect blue wire to location that only  
has power when the headlights are on.  
Recharge or replace vehicle battery.  
Return clock for repair. (contact factory)  
SERVICE AND REPAIR  
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical  
consultation is available to help you work through any questions or problems you may be having installing one  
of our units.  
Should you ever need to send the unit back for repairs, please package the product in a good quality  
box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include a  
complete description of the problem, your full name and address (street address preferred), and a telephone  
number where you can be reached during the day. An authorization number for products being returned for  
repair is not needed. Do not send any money. We will bill you for the repair charges. Any returns for warranty  
work must include a copy of the dated invoice or bill of sale.  
Technical specifications  
Minimum operating voltage  
Maximum operating voltage  
-
-
7 volts  
18 volts  
(operating at or near maximum rating for an extended time can damage unit)  
Clock accuracy  
Typical current draw (@ 13.8V) -  
Standby current draw (key off)  
-
±2 minute per month  
0.13 A  
0.002 A  
-
ODYSSEY SERIES DIGITAL GAUGE LIMITED WARRANTY  
DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and  
condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE, such defect(s) will be  
repaired or replaced (at the Company’s option) without charge for parts or labor directly related to repairs of the defect(s).  
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage  
(e.g. dated bill of sale), name, address, phone number, and specification of defects, transportation prepaid, to the factory. This Warranty is  
valid for the original purchaser only and may not be transferred.  
This warranty does not cover nor extend to damage to vehicle electrical system. This Warranty does not apply to any product or  
part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect,  
or accident.  
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED  
WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR  
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY MUST BE BROUGHT  
WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR  
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,  
WHATSOEVER. No person or representative is authorized to assume for the Company any liability other that expressed herein in  
connection with the sale of this product.  
The Company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF THE COMPANY’S  
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL  
THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID TO THE PURCHASER FOR THE PRODUCT.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if incidental or  
consequential damage so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you  
may also have other rights which vary from state to state.  
4510 W. 61ST St. N., Sioux Falls, SD 57107  
Phone: (605) 332-6513 FAX: (605) 339-4106  
©Copyright 2001 Dakota Digital Inc.  

Kenwood KDC 4023 User Manual
Kenwood DPF R4010 User Manual
Kenwood CD Player KDC 448U User Manual
Kenmore 10082006 User Manual
Jensen MCD5070 User Manual
HTC PURE TOPA210 User Manual
Fujitsu MHR2020AT User Manual
Emerson CK5038 User Manual
DB Link DB Research Computer Drive DB drive User Manual
Bunn Coffeemaker SN FMD0013000 UP User Manual